Find all needed information about Enhanced Pagp Support. Below you can see links where you can find everything you want to know about Enhanced Pagp Support.
https://community.cisco.com/t5/switching/enhanced-pagp/td-p/1103252
Can anyone help me out which devices support Enhanced PAgP. As i need Enhanced PAgP in VSS for dual-active scenario detection.
https://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Campus/VSS30dg/campusVSS_DG/VSS-dg_ch4.html
Enhanced PAgP Support . As described in the preceding section, the neighbor switch must understand enhanced PAgP protocol in order to support dual-active detection. That also means enhanced PAgP requires the PAgP protocol to be operational on in the MEC configuration. One cannot disable PAgP and have enhanced PAgP running.
https://community.cisco.com/t5/switching/4500x-vss-dual-active-detection-with-epagp/td-p/2248707
"Since cross-stack EtherChannel does not support PAgP, it can not use enhanced PAgP for dual ACTIVE detection. Hence the only alternative for cross-stack EtherChannel configuration is to use BFD as a dual ACTIVE detection method" Hope it helps. Regards; Inayath. View solution in original post. 0 Helpful Reply. MARVIN SPITERI.
https://www.cisco.com/c/en/us/products/collateral/switches/catalyst-6800-series-switches/guide-c07-733457.html
Dec 18, 2014 · Today most of the next-generation Cisco or other vendor networking devices support enhanced PAgP or IEEE LACP for dynamic EtherChannel link bundling. However, certain type of systems such as Cisco ISRs, Cisco 5508 WLC, and so on support EtherChannel capabilities in static or nonnegotiate configuration mode instead of dynamic.
https://community.cisco.com/t5/switching/vss-active-dual-detection-via-enhanced-pagp/td-p/2049517
Oct 16, 2012 · Hello all! I have the Cisco VSS consisting two chassis 6509. I have the system Active-Dual detection via Enhanced PAgP with one neighbor - standalone cisco 3750. All works good. I want to add one more neighbor - cisco stack 3750x with 3 members.
https://community.cisco.com/t5/switching/cisco-9400-switch-unable-to-configure-enhanced-pagp/td-p/3913898
Cisco 9400 Switch Unable to configure Enhanced PAGP i want to configure enhanced Dual-active-detection with ePAgP in Cisco 9400 series Switch line card. ... because i thing above commands will support only in Supervisor engine, and i am trying to configure DAD in Line card , epagp any how tomorrow i will visit again to try command. any more ...
https://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Data_Center/vssdc_integrate.html
Mar 20, 2009 · • Enhanced PAgP (EPAgP) • Bidirectional Forwarding Detection (BFD) These are discussed briefly in the sections that follow. Enhanced PAgP . EPAgP leverages MEC as a medium to detect an active/active VSS environment. EPAgP introduces a new type length value (TLV) to the PAgP messages shared between the switches forming the MEC.
https://www.cisco.com/c/dam/en/us/products/collateral/switches/catalyst-3850-series-switches/q-and-a-c67-738577.pdf
• Enhanced PAgP for dual active detection will be supported in future software releases. • In dual active condition, after the SVL connections are fully restored, the user must manually reload the recovery mode stack member switch to join back to the StackWise Virtual domain. • After StackWise Virtual conversion, any addition to or removal
Need to find Enhanced Pagp Support information?
To find needed information please read the text beloow. If you need to know more you can click on the links to visit sites with more detailed data.
