Find all needed information about Netapp Configure Autosupport. Below you can see links where you can find everything you want to know about Netapp Configure Autosupport.
https://kb.netapp.com/app/answers/answer_view/a_id/1030087/~/how-to-configure-autosupport-in-data-ontap-
The AutoSupport feature is enabled by default on the storage system. AutoSupport begins sending messages to technical support 24 hours after it is enabled. Configuration to complete AutoSupport setup: To complete AutoSupport configuration, fill in the following fields: Configure the 'from' address: 7 …
https://kb.netapp.com/app/answers/answer_view/a_id/1030460/~/how-to-set-up-autosupport-
This article describes the procedure to set up the AutoSupport feature on a NetApp storage system. Notes: Systems running in Cluster mode, AutoSupport configuration …
https://library.netapp.com/ecmdocs/ECMP1196798/html/GUID-91C43742-E563-442E-8161-17D5C5DA8C19.html
You can control whether and how AutoSupport information is sent to NetApp technical support and your internal support organization, and then test that the configuration is correct. About this task Perform this procedure on each node in your system where you want to configure AutoSupport.
https://docs.netapp.com/ontap-9/topic/com.netapp.doc.hw-metrocluster-tiebreaker/GUID-EB722A3D-C181-42CB-BBF7-5AEC4AEBD92C.html
By default, AutoSupport messages are sent to NetApp a week after installation of the Tiebreaker software. Events that trigger AutoSupport notification include Tiebreaker software panics, detection of disaster conditions on MetroCluster configurations, or an unknown MetroCluster configuration status.
https://kb.netapp.com/app/answers/answer_view/a_id/1030448/~/how-to-configure-autosupport-for-e-series-systems-
The E2800 and E5700 storage arrays include embedded ASUP functionality, rather than relying on an externally installed Event Monitor (agent provided with SANtricity Storage Manager) to configure and monitor AutoSupport (as does the E2700, E5600, and EF560 storage arrays).
https://library.netapp.com/ecmdocs/ECMLP2855905/html/GUID-57CCBDE0-6EB6-4DDE-94E3-1FFA9C1653FC.html
Select Yes to enable AutoSupport notification to NetApp. Specify the type of delivery ( HTTP, HTTPS, or SMTP) for AutoSupport notification to NetApp technical support. Note: By default, AutoSupport uses port numbers 80 for HTTP, 443 for HTTPS, and 25 for SMTP.
https://library.netapp.com/ecmdocs/ECMP1148877/html/GUID-400E550B-EBE2-4124-9C87-AEA89DBDD0AF.html
You must configure how and where AutoSupport information is sent from each node, and then test that the configuration is correct. AutoSupport messages are scanned for potential problems and are available to technical support when they assist customers in resolving issues.
https://docs.netapp.com/ontap-9/topic/com.netapp.doc.dot-cm-sag/GUID-D4B6F57E-14B6-49F8-BA7E-48736542B69F.html
Set up AutoSupport or modify the configuration of AutoSupport system node autosupport modify Enable and disable AutoSupport messages to your internal support organization for individual trigger events, and specify additional subsystem reports to include in messages sent in …
https://docs.netapp.com/ontap-9/topic/com.netapp.doc.dot-cm-sag/GUID-91C43742-E563-442E-8161-17D5C5DA8C19.html
Check that addresses are correctly configured by listing the destinations using the system node autosupport destinations show command.; If you are sending messages to your internal support organization or you chose SMTP transport for messages to technical support, configure SMTP by setting the following parameters of the system node autosupport modify command:
https://library.netapp.com/ecmdocs/ECMP1196798/html/GUID-DF931E89-B833-4DED-83B5-A97F7EC97425.html
AutoSupport is a mechanism that proactively monitors the health of your system and automatically sends messages to NetApp technical support, your internal support organization, and a support partner. Although AutoSupport messages to technical support are enabled by default, you must set the correct options and have a valid mail host to have messages sent to your internal support organization.
Need to find Netapp Configure Autosupport information?
To find needed information please read the text beloow. If you need to know more you can click on the links to visit sites with more detailed data.
