Find all needed information about Non Cisco Wgb Support. Below you can see links where you can find everything you want to know about Non Cisco Wgb Support.
https://www.cisco.com/c/en/us/support/docs/wireless/aironet-1130-ag-series/113198-wgb-roam-config.html
Aug 26, 2011 · Non Cisco WGB: This is a third party device acting as a WGB, connecting one or more wired devices to the wireless infrastructure. These do not support IAPP, and either allow only a single wired device, or provide a MAC address translation mechanism, hiding all their wired clients behind a single 802.11 MAC address.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-3/config-guide/b_cg83/b_cg83_chapter_0101100.html
Jun 15, 2018 · Restrictions for Non-Cisco Workgroup Bridges. Only Layer 2 roaming is supported for WGB devices. Layer 3 security (web authentication) is not support for WGB clients. Visibility of wired hosts behind a WGB on a controller is not supported because the non-Cisco WGB device performs MAC hiding. Cisco WGB supports IAPP.
https://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/crn7_0_116_0.html
Non-Cisco WGB Support. Starting in release 7.0.116.0, the controller software has been updated to accommodate non-Cisco workgroup bridges so that the controller can forward ARP, DHCP, and data traffic to and from the wired clients behind workgroup bridges. This processes is accomplished by enabling the passive client feature.
https://community.cisco.com/t5/other-wireless-mobility-subjects/wgb-workgroup-bridge-only-works-in-universal-mode/td-p/2825938
Just to verify: yes, you need to have the "Aironet IE extensions" enabled on your SSID to support the "default" WGB Cisco implementation. When you use "universal mode" the access-point spoofs the specified MAC address so that the wireless infrastructure has no idea that the access-point is in between.
https://community.cisco.com/t5/other-wireless-mobility-subjects/unstable-wgb-on-wlc/td-p/1958770
The Non-Cisco WGB feature is supported only on the 5508, 2500 and 2100 Controllers. NPU based platforms (4400/wism/3750w) do not support this feature. #however, you could try adding the 3rd party wgb mac address to WLC's mac filter list and test with simple to …
https://community.cisco.com/t5/other-wireless-mobility-subjects/can-you-connect-non-cisco-ap-s-to-a-cisco-wlc-controller/td-p/1342711
Re: Can you connect non-cisco AP's to a Cisco WLC Controller There are a number of "foreign AP" subcommands found in CLI but there are no official documentations as of yet. For obvious reasons, Cisco will officially "not"support non-Cisco LAP to their WLC.
https://community.cisco.com/t5/wireless-and-mobility/ap1262-bridge-to-non-cisco-access-point/td-p/2456976
I would like to use a Cisco AP1262 in a mobile command vehicle to bridge to any WiFi Access Point that I know the SSID and Pasword to. Will the 1262 Bridge to a Non-Cisco Access Point? If so, any assistance in finding an example configuration would
https://www.cisco.com/c/en/us/support/docs/wireless/aironet-340-series/8018-workgroup-bridge-faq.html
Jul 31, 2007 · The 340 WGB runs VxWorks, and new Cisco IOS products (such as the br1310) have adapted the WGB, root/non-root bridge, and AP functionality. Q. What is the default IP address of a WGB? A. ... A Cisco WGB device does not support multiple VLANs in it. A 1100 AP, however, that acts in WGB mode can support multiple VLANs in it but with these ...
https://community.cisco.com/t5/wireless-mobility-documents/universal-workgroup-bridge-feature-on-autonomous-access-points/ta-p/3132608
Core Issue. 1200 series autonomous access points can support Universal Workgroup Bridge mode. With this feature , access point configured in workgroup bridge mode can also associate to non-cisco APs.WGB assoicates as a client and only a single wired client can be connected with the Universal WGB.
Need to find Non Cisco Wgb Support information?
To find needed information please read the text beloow. If you need to know more you can click on the links to visit sites with more detailed data.
