Find all needed information about Send Autosupport Netapp Command Line. Below you can see links where you can find everything you want to know about Send Autosupport Netapp Command Line.
https://kb.netapp.com/app/answers/answer_view/a_id/1036282/~/how-to-manually-send-autosupport-files-to-netapp-
The AutoSupport message is too big in size to fit through the mail servers size filter/policy. AutoSupport messages were not sent for whatever reason, and they need to be collected for analysis. This article describes the procedure to be followed to manually send AutoSupport files to NetApp.
https://library.netapp.com/ecmdocs/ECMP1366832/html/system/node/autosupport/invoke.html
The system node autosupport invoke command sends an AutoSupport message from a node ... Use this parameter to specify text sent in the subject line of the AutoSupport message. This parameter is not available when the -type parameter ... Use this parameter to send the AutoSupport message to the destination you specify instead of the configured ...
https://docs.netapp.com/ontap-9/topic/com.netapp.doc.dot-cm-sag/GUID-D4B6F57E-14B6-49F8-BA7E-48736542B69F.html
You use the system node autosupport commands to change or view AutoSupport configuration, display information about previous AutoSupport messages, and send, resend or …
https://library.netapp.com/ecmdocs/ECMP1155684/html/GUID-D4B6F57E-14B6-49F8-BA7E-48736542B69F.html
You use the autosupport and options autosupport commands to change or view AutoSupport configuration, display information about past AutoSupport messages, and …
https://kb.netapp.com/app/answers/answer_view/a_id/1031570/~/how-to-manually-trigger-a-complete-autosupport-for-clustered-data-ontap-from
-node is the name of the node you want the AutoSupport from. An '*' can be used as a wild card for all nodes.-type is the type of AutoSupport. The types are test, performance or all. Examples: To trigger a complete AutoSupport for all nodes, type: autosupport invoke -node * -type all To trigger a performance AutoSupport for node filer-NAS-01 type:
https://docs.netapp.com/ontap-9/topic/com.netapp.doc.dot-cm-cmpr-930/system__node__autosupport__invoke.html
This parameter has effect only if performance AutoSupport messages are enabled, which is controlled by the -perf parameter of the system node autosupport modify command. [-uri <text>] - Alternate Destination for This AutoSupport Use this parameter to send the AutoSupport message to the destination you specify instead of the configured destination.
http://pientarteknik.com/wp/how-to-manually-send-autosupport-messages-to-netapp/
Send the e-mail to [email protected]. Once NetApp receives the AutoSupport e-mail, assuming that it is in the correct format, it might take 24 – 48 hours for the initial AutoSupport to be displayed in My AutoSupport on the NetApp Support site. Note: Regularly sending AutoSupport messages will decrease this processing time.
https://www.youtube.com/watch?v=QBnlmJD1NqE
Aug 16, 2013 · This video demonstrates how to manually send AutoSupport messages to NetApp in circumstances where it cannot be sent automatically over the internet.Author: NetApp KB TV
https://darrenabme.files.wordpress.com/2015/07/netapp-trigger-autosupport-from-command-line.pdf
Netapp Trigger Autosupport From Command Line The message is included in the subject line of the AutoSupport notification and You can use the autosupport trigger show command to display AutoSupport. system node autosupport invoke - node anyfiler-01 -message case_number/1234567 - type all. Netapp cluster mode command basicsIn "cDot". Netapp cluster.
https://www.netapp.com/us/documentation/eseries-santricity.aspx
E-Series systems give you an integrated hardware and software solution for dedicated, high-bandwidth applications like data analytics, video surveillance, and disk-based backup that …
Need to find Send Autosupport Netapp Command Line information?
To find needed information please read the text beloow. If you need to know more you can click on the links to visit sites with more detailed data.
